ExxonMobil Jet Fuel
ExxonMobil commercial-fuel , Tanzania
Jet A and Jet A-1 are kerosene-type fuels. The primary difference between the two is freeze point, the temperature at which wax crystals disappear in a laboratory test.
Jet A, which is mainly used in the United States, must have a freeze point of minus 40ºC or below and does not typically contain static dissipator additive. Jet A-1 must have a freeze point of minus 47ºC or below and for locations outside the United States, this fuel normally contains static dissipator additive. There are other key differences between the manufacturing specification within the United States and Europe/Africa/Middle East/Australasia.
Def. Stan. 91-91 has an additional requirement for lubricity for Jet A-1.
ExxonMobil Jet A and ExxonMobil Jet A-1 meet the requirements of ASTM D1655 Standard Specification for Aviation Turbine Fuels. ExxonMobil Jet A-1 also complies with U.K. DEF STAN 91-91, and the JIG (Joint Inspection Group) Aviation Fuel Requirements for Jointly Operated Systems (Check List). In all cases, the most recent issue of relevant specifications applies to the product supplied.
|ExxonMobil Jet A meets the following industry specifications:||ExxonMobil Jet A||ExxonMobil Jet A-1|
|ASTM D 1655||X||X|
|Military||ExxonMobil Jet A||ExxonMobil Jet A-1|
|Approved against Mil U.K. DEF STAN 91-91||Not applicable||X|
|Approved against Mil and the JIG (Joint Inspection Group) Aviation Fuel Requirements for Jointly Operated Systems (Check List)||Not applicable||X|
|Jet A||Jet A-1|
|Acidity, mg KOH/g||0.10 Max.||0.10 Max.|
|Aromatics, Vol. %||25 Max.||25.0 Max.ax.|
|Sulphur, mercaptan, Wt. %||0.003 Max.||0.003 Max.|
|Sulphur, total, Wt. %||0.30||0.30|
|10% Distillation, ºC||205 Max.||205.0 Max.|
|Final Boiling Point, ºC||300 Max||300.0 Max|
|Distillation Residue, %||1.5 Max.||1.5 Max.|
|Distillation Loss, %||1.5 Max.||1.5 Max.|
|Flash Point, ºC||38 Min.||38.0 Min.|
|Density @ 15ºC, kg/m3||775/840||775/840.0|
|Freeze Point, ºC||-40 Max||-47.0 Max|
|Viscosity @ -20ºC, mm/s||8.0 Max.||8.0000 Max.|
|Net Heat of Combustion, MJ/kg||42.8 Min.||42.80 Min.|
|One of the following shall be met|
|1) Smoke Point, mm, or||25 Min.||25.0 Min.|
|2) Smoke Point, mm, and||18 Min.||19.0 Min.|
|Naphthalenes, Vol. %||3.0 Max||3.00 Max|
|Copper Strip Corrosion, 2 h % 100ºC||No. 1||No. 1|
|Filter pressure drop, mm Hg||25 Max.||25 Max.|
|Tube Deposits||< 3 Max.||< 3 Max.|
|Existent Gum, mg/100 mL.||7 Max.||7 Max.|
|Water Reaction, Interface Rating||1b Max.||1b Max.|
|Without electrical conductivity additive||85||85|
|With electrical conductivity additive||70||70|
|Electrical conductivity, pS/m||50 Min. 600 Max.|
Health and Safety
Based on available information, this product is not expected to produce adverse effects on health when used for the intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDSs are available via the Internet at ExxonMobil.com. This product should not be used for purposes other than its intended use.
MAIN HAZARD: FIRE
Keep away from ignition sources.
Discharge your static electricity before fueling.
Fill portable containers on the ground.
Handle/Transport in closed or properly vented containers and systems, consistent with all applicable laws.
Harmful or fatal if swallowed.
Avoid breathing the vapors and skin contact.
Do not wash down spills with water. Prevent all spills from reaching water.
The Exxon logotype, the Running Tiger are trademarks of ExxonMobil Corporation, or one of its subsidiaries.05-2020